// SPDX-License-Identifier: GPL-2.0-only

/dts-v1/;

#include <dt-bindings/arm/qcom,ids.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "sdm845.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"

/delete-node/ &mpss_region;
/delete-node/ &venus_mem;
/delete-node/ &cdsp_mem;
/delete-node/ &mba_region;
/delete-node/ &slpi_mem;
/delete-node/ &spss_mem;
/delete-node/ &rmtfs_mem;

/ {
	chassis-type = "handset";
	qcom,board-id = <0x00021505 0>;
	qcom,msm-id = <QCOM_ID_SDM845 0x20001>;

	aliases {
		serial0 = &uart9;
		serial1 = &uart6;
	};

	battery: battery {
		compatible = "simple-battery";
	};

	chosen {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		stdout-path = "serial0:115200n8";

		/* Use display framebuffer as setup by bootloader */
		framebuffer0: framebuffer-0 {
			compatible = "simple-framebuffer";
			memory-region = <&cont_splash_mem>;

			format = "a8r8g8b8";
		};
	};

	reserved-memory {
		cont_splash_mem: splash@9d400000 {
			reg = <0 0x9d400000 0 0x02400000>;
			no-map;
		};

		mpss_region: memory@8e000000 {
			reg = <0 0x8e000000 0 0x9800000>;
			no-map;
		};

		venus_mem: venus@97800000 {
			reg = <0 0x97800000 0 0x500000>;
			no-map;
		};

		cdsp_mem: cdsp-mem@97D00000 {
			reg = <0 0x97D00000 0 0x800000>;
			no-map;
		};

		mba_region: mba@98500000 {
			reg = <0 0x98500000 0 0x200000>;
			no-map;
		};

		slpi_mem: slpi@98700000 {
			reg = <0 0x98700000 0 0x1400000>;
			no-map;
		};

		spss_mem: spss@99B00000 {
			reg = <0 0x99B00000 0 0x100000>;
			no-map;
		};

		rmtfs_mem: rmtfs-region@f2700000 {
			compatible = "qcom,rmtfs-mem";
			reg = <0 0xf2700000 0 0x202000>;
			qcom,use-guard-pages;
			no-map;

			qcom,client-id = <1>;
			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
		};
	};

	gpio-keys {
		compatible = "gpio-keys";
		label = "Volume keys";
		autorepeat;

		pinctrl-0 = <&volume_up_gpio>;
		pinctrl-names = "default";

		key-vol-up {
			label = "Volume Up";
			linux,code = <KEY_VOLUMEUP>;
			gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
			debounce-interval = <15>;
		};
	};

	vph_pwr: regulator-vph-pwr {
		compatible = "regulator-fixed";
		regulator-name = "vph_pwr";
		regulator-min-microvolt = <3700000>;
		regulator-max-microvolt = <3700000>;
	};

	vreg_s4a_1p8: regulator-vreg-s4a-1p8 {
		compatible = "regulator-fixed";
		regulator-name = "vreg_s4a_1p8";

		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		regulator-always-on;
		regulator-boot-on;

		vin-supply = <&vph_pwr>;
	};
};

&adsp_pas {
	firmware-name = "qcom/sdm845/Google/blueline/adsp.mbn";

	status = "okay";
};

&apps_rsc {
	regulators-0 {
		compatible = "qcom,pm8998-rpmh-regulators";
		qcom,pmic-id = "a";

		vdd-s1-supply = <&vph_pwr>;
		vdd-s2-supply = <&vph_pwr>;
		vdd-s3-supply = <&vph_pwr>;
		vdd-s4-supply = <&vph_pwr>;
		vdd-s5-supply = <&vph_pwr>;
		vdd-s6-supply = <&vph_pwr>;
		vdd-s7-supply = <&vph_pwr>;
		vdd-s8-supply = <&vph_pwr>;
		vdd-s9-supply = <&vph_pwr>;
		vdd-s10-supply = <&vph_pwr>;
		vdd-s11-supply = <&vph_pwr>;
		vdd-s12-supply = <&vph_pwr>;
		vdd-s13-supply = <&vph_pwr>;
		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
		vdd-l6-supply = <&vph_pwr>;
		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
		vdd-l9-supply = <&vreg_bob>;
		vdd-l10-l23-l25-supply = <&vreg_bob>;
		vdd-l13-l19-l21-supply = <&vreg_bob>;
		vdd-l16-l28-supply = <&vreg_bob>;
		vdd-l18-l22-supply = <&vreg_bob>;
		vdd-l20-l24-supply = <&vreg_bob>;
		vdd-l26-supply = <&vreg_s3a_1p35>;
		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;

		vreg_s3a_1p35: smps3 {
			regulator-min-microvolt = <1352000>;
			regulator-max-microvolt = <1352000>;
		};

		vreg_s5a_2p04: smps5 {
			regulator-min-microvolt = <1904000>;
			regulator-max-microvolt = <2040000>;
		};

		vreg_s7a_1p025: smps7 {
			regulator-min-microvolt = <900000>;
			regulator-max-microvolt = <1028000>;
		};

		vdda_mipi_dsi0_pll:
		vreg_l1a_0p875: ldo1 {
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <880000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-boot-on;
		};

		vreg_l5a_0p8: ldo5 {
			regulator-min-microvolt = <800000>;
			regulator-max-microvolt = <800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l12a_1p8: ldo12 {
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l7a_1p8: ldo7 {
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l13a_2p95: ldo13 {
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <2960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l14a_1p8: ldo14 {
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-boot-on;
			/*
			 * We can't properly bring the panel back if it gets turned off
			 * so keep it's regulators always on for now.
			 */
			regulator-always-on;
		};

		vreg_l17a_1p3: ldo17 {
			regulator-min-microvolt = <1304000>;
			regulator-max-microvolt = <1304000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l19a_3p3: ldo19 {
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3312000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			/*
			 * The touchscreen needs this to be 3.3v, which is apparently
			 * quite close to the hardware limit for this LDO (3.312v)
			 * It must be kept in high power mode to prevent TS brownouts
			 */
			regulator-allowed-modes = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l20a_2p95: ldo20 {
			regulator-min-microvolt = <2960000>;
			regulator-max-microvolt = <2968000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l21a_2p95: ldo21 {
			regulator-min-microvolt = <2960000>;
			regulator-max-microvolt = <2968000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l24a_3p075: ldo24 {
			regulator-min-microvolt = <3088000>;
			regulator-max-microvolt = <3088000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l25a_3p3: ldo25 {
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3312000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vdda_mipi_dsi0_1p2:
		vreg_l26a_1p2: ldo26 {
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-boot-on;
		};

		vreg_l28a_3p0: ldo28 {
			regulator-min-microvolt = <2856000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
			regulator-boot-on;
			/*
			 * We can't properly bring the panel back if it gets turned off
			 * so keep it's regulators always on for now.
			 */
			regulator-always-on;
		};
	};

	regulators-1 {
		compatible = "qcom,pmi8998-rpmh-regulators";
		qcom,pmic-id = "b";

		vdd-bob-supply = <&vph_pwr>;

		vreg_bob: bob {
			regulator-min-microvolt = <3312000>;
			regulator-max-microvolt = <3600000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
			regulator-allow-bypass;
		};
	};

	regulators-2 {
		compatible = "qcom,pm8005-rpmh-regulators";
		qcom,pmic-id = "c";

		vdd-s1-supply = <&vph_pwr>;
		vdd-s2-supply = <&vph_pwr>;
		vdd-s3-supply = <&vph_pwr>;
		vdd-s4-supply = <&vph_pwr>;

		vreg_s3c_0p6: smps3 {
			regulator-min-microvolt = <600000>;
			regulator-max-microvolt = <600000>;
		};
	};
};

&cci {
	status = "okay";
};

&cci_i2c1 {
	/* actuator @0c */

	/* front camera, imx355 @1a */

	/* eeprom @50, at24 driver says 8K */
};

&cdsp_pas {
	firmware-name = "qcom/sdm845/Google/blueline/cdsp.mbn";

	status = "okay";
};

&gcc {
	protected-clocks = <GCC_QSPI_CORE_CLK>,
			   <GCC_QSPI_CORE_CLK_SRC>,
			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
};

&gpi_dma0 {
	status = "okay";
};

&gpi_dma1 {
	status = "okay";
};

&gpu {
	status = "okay";
};

&gpu_zap_shader {
	firmware-name = "qcom/sdm845/Google/blueline/a630_zap.mbn";
};

&i2c12 {
	/* Bottom spkr (right) CS35L36 @ 40 */

	/* Top spkr (left) CS35L36 @ 41 */
};

&ipa {
	firmware-name = "qcom/sdm845/Google/blueline/ipa_fws.mbn";
	memory-region = <&ipa_fw_mem>;

	status = "okay";
};

&mdss {
	status = "okay";
};

&mss_pil {
	firmware-name = "qcom/sdm845/Google/blueline/mba.mbn",
			"qcom/sdm845/Google/blueline/modem.mbn";

	status = "okay";
};

&pm8998_gpios {
	volume_up_gpio: vol-up-active-state {
		pins = "gpio6";
		function = "normal";
		input-enable;
		bias-pull-up;
		qcom,drive-strength = <0>;
	};
};

&pm8998_resin {
	linux,code = <KEY_VOLUMEDOWN>;

	status = "okay";
};

&pmi8998_charger {
	monitored-battery = <&battery>;

	status = "okay";
};

&qupv3_id_0 {
	status = "okay";
};

&qupv3_id_1 {
	status = "okay";
};

&qup_uart9_rx {
	drive-strength = <2>;
	bias-pull-up;
};

&qup_uart9_tx {
	drive-strength = <2>;
	bias-disable;
};

&tlmm {
	gpio-reserved-ranges = < 0 4>, /* SPI (Intel MNH Pixel Visual Core) */
			       <81 4>; /* SPI (most likely Fingerprint Cards FPC1075) */

	touchscreen_reset: ts-reset-state {
		pins = "gpio99";
		function = "gpio";
		drive-strength = <8>;
		bias-pull-up;
	};

	touchscreen_pins: ts-pins-gpio-state {
		pins = "gpio125";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	touchscreen_i2c_pins: qup-i2c2-gpio-state {
		pins = "gpio27", "gpio28";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};
};

&uart6 {
	pinctrl-0 = <&qup_uart6_4pin>;

	status = "okay";

	bluetooth {
		compatible = "qcom,wcn3990-bt";

		vddio-supply = <&vreg_s4a_1p8>;
		vddxo-supply = <&vreg_l7a_1p8>;
		vddrf-supply = <&vreg_l17a_1p3>;
		vddch0-supply = <&vreg_l25a_3p3>;
		max-speed = <3200000>;
	};
};

&uart9 {
	status = "okay";
};

&ufs_mem_hc {
	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;

	vcc-supply = <&vreg_l20a_2p95>;
	vcc-max-microamp = <800000>;

	status = "okay";
};

&ufs_mem_phy {
	vdda-phy-supply = <&vreg_l1a_0p875>;
	vdda-pll-supply = <&vreg_l26a_1p2>;

	status = "okay";
};

&usb_1 {
	status = "okay";
};

&usb_1_dwc3 {
	dr_mode = "peripheral";
};

&usb_1_hsphy {
	vdd-supply = <&vreg_l1a_0p875>;
	vdda-pll-supply = <&vreg_l12a_1p8>;
	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;

	qcom,imp-res-offset-value = <8>;
	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;

	status = "okay";
};

&usb_1_qmpphy {
	vdda-phy-supply = <&vreg_l26a_1p2>;
	vdda-pll-supply = <&vreg_l1a_0p875>;

	status = "okay";
};

&venus {
	firmware-name = "qcom/sdm845/Google/blueline/venus.mbn";

	status = "okay";
};

&wifi {
	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;

	qcom,snoc-host-cap-8bit-quirk;

	status = "okay";
};